Tuesday, June 29, 2010

snowmobile drag racing parts

snowmobile drag racing is a cheap easy way to go fast at the drag strip ,it will cost you about 1,200-1,500 dollars to set up your snowmobile you will need  wheels and a slick track and also you will need to get some safety gear also a helmet ,suit,and  boots what ever your track will allow you to wear when you run snow machine .
snowmobile drag racing parts the way to start racing asphalt drag racing at your local strip all you need is a set of asphalt skis and a slick or smooth rear track .check with your local track on the safety gear might need before you head out to the track to run your snowmobile .



snomobile asphalt racing front wheels for your asphalt drag racing snomobile
Wahl Bros. has designed tough, lightweight aluminum skis for asphalt racing. Available with two or four wheels and in Aluminum or Black Powder Coat, these asphalt skis feature the newest wheel innovation available. Billet aluminum wheels with a high grade polyurethane molded on make for a wheel that can handle speed and friction like no other wheel available. The asphalt Skis with two wheels weigh 4 lbs. 2 oz. each, while skis with four wheels weigh 5 lbs 4 oz. each. NHRA & ISR approved. Sold in pairs. (Pictured are the 03-239A Skis w/four wheels) for more info click on the link


                                                            Proline Small Asphalt Ski
                                                  Best asphalt ski for the past five years.

                                              Rubber mounted ski loops to resist cracking

                                                   Avail in in 2.25" and 3.0" widths



The new 2010 asphalt skis are the most durable ski on the market! With a dual bearing wheel and re-designed heavy duty ski loops that resist cracking. The new asphalt skis have black anodized plates that have been re-designed for your full run out. The new ski wheels are available in black or red and have run over 177 mph consistently.




The new big wheel skis have 5.75" dia. dual roller bearings to reduce heat. The 5.5 diameter wheel slows the bearing speed down. Designed with dual bearings and large cooling aluminum hubs for added safety


slick snowmobile drag racing track

Sunday, June 27, 2010

corvette doing a burnout


1970 - 1980 corvette not sure what year is the corvette doing a small burnout norridge or chicago IL at night harlem and higgins seems like the car built it sounded like it but with a stock apperece t-tops night cruising in illinois

Saturday, June 26, 2010


Short Sand Cars Single Seat and Two Seat, Little Sahara Sand Dunes, 1300 Hayabusa Turbo Motor, Awesom Wheelies sand rail in action



chasing a sand rail

hayabusa sand rail


2004 Hayabusa two seater, Built by Short Sand Cars

DRAG RACING ASPHALT jet powered ATV



ATV AND MOTORCYCLE JET V\S ATV SNOWMOBILE ENGINE ALCOHOL USA V\S PR IN 1/4 MILE 9.5 SECONDS the snowmobile atv looks to be faster than the jet one, but the jet one is cooler the jet bike is out of control as far as you got to be nuts to ride that atv.



MOTORCYCLE JET USA V/S ATV GAS PR PART II

Thursday, June 24, 2010

Merlin V12 Powered 55 Chevy


baddest 55 chevy as you can see the massive engine and one of a kind custom paint job
Merlin V12 Powered 55 Chevy

1125r buell 10.05et at santapod 18.04.09


this is a 1125r buell running stock motor, wheelbase and foot shifting with the clutch
runs very fast for a stock bike 10.05et 139mph very nice bike.

Tuesday, June 22, 2010

Diesel motorcycle


Home made Diesel Bike on old Soviet Ural (M) frame 3 cylinder, 650 cc Diesel Engine

Sunday, June 20, 2010

Dieselcare at the TS Performance Outlaw Diesel Drag Race


more diesel action banks diesel drag truck diesel funny car diesel dragster was held at TS Performance Outlaw Series Diesel Drag race held at Beech bend in Bowling Green, KY

Diesel Funny car





one real nice Diesel Power Funnycar at Competition Diesel Invitation in Steele, Alabama
Top Fuel funny car chassis and body with a Cummins diesel engine with turbo AND nitrous.

Thursday, June 17, 2010

Jesse Rooke 3 wheel vehicle

Jesse Rooke of Rooke Customs award winning bike builder ,this is my favorite bike builder out their very high quality bike builds Jesse Rooke of Rooke Customs explains why this nearly 200hp Three-Wheeler, he calls the "Rooke"ster, was built and compares it to other street vehicles.






Jesse Rooke 2009 SEMA Show

margie chopper
motoGP





darla bike

Phyllis chopper

S&S Tour Bike


Rossmeyer Flyer
http://www.rookecustoms.com/

Wednesday, June 16, 2010

Knockout Motorcycle Co. Rockem Rocket

Knockout Motorcycle Co. Rockem Rocket
96 in. s&s motor
paint done by AJ’S CUSTOMS
front suspension KIWI LEAF SPRING / STOCK LENGTH
WHEELS: EXTREME MACHINE – 23” FRONT & REAR
http://www.ralphrandolph.com/


Sunday, June 13, 2010

Blown '32 Ford Coupe - High 8's Low 9's Street Leg


real nice fast blown 32 ford 468 ci big block bds 8-71 blower dual pro form 950 carbs t-400 trans 3000 stall converter 31 x 18.5 slicks

Saturday, June 12, 2010

sand rail


a nice home built sand rail
It took me over 2000 hour to build this buggy and now its finally ready. I have design and construct the whole buggy myself
please tell me what you think about it.
Its got a honda cbr 929rr fireblad motocycle engine 150 hp.
front suspension travel about 25 inches and 28" in the rear
it has 2" bypass fox shocks. frame and suspension made from 1"
chromoly tubing, all tig welded and powder coated. itp mud lite 30"
tires on t7 beadlocks. weigh about 1100 pounds and accelerates from 0-60 mph in about 4.5 sec, topspeed 100 mph.





buggy doing some crazy jumping almost flipping over

Friday, June 11, 2010

Mike Lavallee flame painting


Mike Lavallee airbrush painting true fire or realistic fire on a car real nice paint job their check it out.do you think it is a nice paint job.

Thursday, June 10, 2010

buggy build 08-09





This is our "little" project that we started last sommer! its powered by a Kawasaki GPX750 motor out of the late 80`s. Tts not quite done. there are still things that i have to do like the cooling, gas tank, brakes and and and... but when its done, it will wheigh around 350 kg. thats 3.5kg/hp!!! better then a Porsche 911

Selfmade Honda VFR 750ccm Buggy



It took us nearly one year and a lot of sweat and blood to finish this vehicle. Some details:
The engine is from a 110 Hp strong Honda motorcycle and has a torque of 60Nm , it's weight is 385kg. The brakes are out of an old VW Käfer. Small parts were bought all the over were made by ourselves.

Kid does awesome sandrail wheelie at Glamis Dunes.


10 year old E.G. does awesome 55 mph quarter mile wheelie in a sandrail at Glamis Dunes CA. kid doing big wheelies this is nuts i wish i had a dad like this we all wish.

Sunday, June 6, 2010

Willys Pickup Blown 468 Big Block Chev


41 will's truck build
First day starting up the 468 Blown Big Block Chev.

blown injected 41 willys 2




41 willy's blown and injected hemi v8 the heads if you look close the car has 2 spark plugs per cylender and a old school injection system zoomies side pipes and tubbed out
the car is a perfect 10

Blown EH


blown and injected street machine

Thursday, June 3, 2010